• <table id="uus6w"><option id="uus6w"></option></table>
  • <table id="uus6w"></table>
  • Products

    Contact Us

    Wuxi mingschin machine tool co., LTD
    Telephone: +86 510-85620588
    Tel: +86 510-85626818
    Fax: +86 510-85627361
    Email: mxjc@www.5huc.com
    Url: www.www.5huc.com
    AddNo. 1 Huayi Road, Binhu Economic Development Zone, Wuxi, Jiangsu, China

    MX-400/S

    作者:admin 發布時間:2021/03/31 瀏覽量:2126

    bbf7bb97576fe2924b28398f2c318df


    Main Characteristics:

    MX-400 CNC Vertical Grinder is a universal grinder with joint travel over 4 axes by using Siemens 828D control system. One clamping can grind various special shapes such as ID, OD, end face,  surface of the part.

    It adopts a double-grinding frame structure. According to the needs of processing parts, two vertical grinding spindles can be selected; one vertical grinding head and one horizontal grinding spindle. Both vertical and horizontal high-precision grinding spindles are driven by frequency converters for speed regulation. The rotating speed of the grinding spindle can be equipped with high and low speed according to the required processing size.

    The guide rail adopts Japanese THK roller guide with high precision and high vibration resistance. The ball screw adopts high-precision THK ball screw.

    The workpiece spindle adopts a sleeve spindle, and the bearing adopts a high-precision grouped angular contact spindle bearing.

    Vertical grinding frames adopts the hydraulic balance device to balance the gravity, which improves the balance when moving up and down and the life of the executive components.

    The machine guide rails and ball screws are automatically lubricated by the lubrication station. And there are sealed covers for protection.

    The machine can be equipped with pneumatic pitch circle positioning gear automatic fixture, three-jaw fixture, four-jaw fixture, electromagnetic chuck and various special fixtures.

    Grinding coolant filter adopts magnetic and paper precision filter device.

    The machine tool can be equipped with a diamond roller dresser and a single-point diamond pen dresser.

    The machine’S X1、X2、Z1 and Z2 servo axis can adopt the Heidenhain linear encoders to form a closed-loop control.

    The machine tool adopts a fully enclosed housing, and an optional oil mist separator.


    Main Application:

    It is mainly used for precision grinding of ID, OD, end faces, and conical surfaces of disk-shaped parts such as gears, bearings, and shaft sleeves. The grinding of each surface is completed at one time to ensure the position accuracy of each grinding surface. It is a new generation of high-precision and high-efficiency production machine tools. The entire grinding cycle of the machine tool is automatically completed, and the operator only needs to assemble and disassemble the workpiece. This machine tool is especially suitable for mass production of gears and bearing rings.


    Machining accuracy:

    圓度Roundness

    0.0015mm

    圓柱度Cylintricty

    0.0025mm

    同軸度 Coaxality

    0.004mm

    垂直差

    0.004mm

    表面粗糙度Surface roughness

    Ra0.32μm


    Main Specifications:

    立磨頭磨削                                                                                                              Ф50mm-Ф350mm

    最大磨削深度Maximum grinding bore length                                                                   300mm

    最大磨削外徑Maximum OD to be ground                                                                         Ф400mm

    工件最大回轉直徑Max. swing diameter of the worktable                                                   Ф400mm

    橫梁滑板行程(X1、X2)Stroke of horizontal slide on cross beam(Axis X1 and X2)             600mm

    磨架上、下往復行程(Z1、Z2)Stroke of vertical slide(Axis Z1and Z2)                               420mm

    工件主軸轉速(無級調速)Workspindle speed(stepless speed change)                                    10300r/min

    X1、X2、Z1、Z2軸最高速度Max. moving speed of Axis X1,X2,Z1 and Z2                          6m/min 

    X1、X2、Z1、Z2軸分辨率Resolution of Axis X1,X2,Z1 and Z2                                          0.001mm 

    工作臺最大承Max. loading ability of worktable                                                               200kg

    機床總功率Total power                                                                                                   55KW

    機床外形尺寸Overall dimension of the machine                                                               2602352800mm

    機床重量Weight of the machine                                                                                     8500kg



    Consultation

    免费无码又爽又刺激高潮的视频,免费观看AV福利片,一区二区三区波多野结衣在线观看,久久婷婷人人澡人爽人人喊
  • <table id="uus6w"><option id="uus6w"></option></table>
  • <table id="uus6w"></table>